Engineering report · reviewed against NEC 2026 & BS 7671:2018+A2
Engineering Breakdown: Running a Single-Burner Portable Induction Cooktop on the EcoFlow Delta 3 Plus
When pairing the EcoFlow Delta 3 Plus (1,024 Wh LiFePO4 capacity, 1,800 W continuous, 3,600 W surge) with a Single-Burner Portable Induction Cooktop (1,800 W running, 1,850 W starting surge), the system operates at 100% of continuous inverter capacity on a 120 V North American circuit and 100% on a 230 V UK/EU/AU circuit. At a 100% duty cycle and 85% inverter efficiency, a full battery delivers roughly 29 min of off-grid runtime. Wiring the connection over a 25 ft run calls for a 20 A breaker and 12 AWG copper, terminated at a NEMA 5-15P / 5-20P connection.
1. Compatibility Verdict & Inverter Load Utilization
In North American mode the Single-Burner Portable Induction Cooktop loads the EcoFlow Delta 3 Plus's inverter to 100% of its 1,800 W continuous rating and 51% of its 3,600 W surge rating. The pairing works, but running above 80% for hours raises internal temperatures and fan noise, and leaves little room for other loads. Treat it as a dedicated circuit.
| Check | Load requires | EcoFlow Delta 3 Plus provides | US/NA | UK/EU/AU |
|---|---|---|---|---|
| Continuous output | 1,800 W | 1,800 W | Pass | Pass |
| Start-up surge | 1,850 W | 3,600 W | Pass | Pass |
| Voltage | 120 V / 230 V | 120 V / 230 V | Pass | Pass |
| Connection | NEMA 5-15P / 5-20P | NEMA 5-20R | UK/EU/AU: BS 1363 13A / Schuko CEE 7/4 / AS/NZS 3112 10A | |
This appliance is predominantly resistive or electronically controlled: its 1,850 W start-up figure is within 3% of its 1,800 W running draw, so surge capacity is rarely the bottleneck. What matters is sustained output and energy: heating elements draw full power for as long as they are on, which drains a 1,024 Wh battery quickly. Running it during solar production hours is the most efficient strategy.
As a portable power station, the EcoFlow Delta 3 Plus integrates the LiFePO4 battery, inverter, MPPT solar controller and AC outlets in one chassis, so it can be wheeled to the load or connected to a transfer switch through its NEMA 5-20R outlet.
2. Real-World Runtime by Duty Cycle
Nameplate capacity is not usable capacity. DC-to-AC conversion, battery management overhead and cell protection reduce the 1,024 Wh rating to about 870 Wh of deliverable AC energy (85% system efficiency). Duty cycle is the share of each hour the load actually draws its running power — thermostats, pressure switches and intermittent use all lower it.
| Duty cycle | Average draw | Runtime (no solar) | Energy per 24 h |
|---|---|---|---|
| 25% | 450 W | 1.9 hrs | 10.8 kWh |
| 50% | 900 W | 58 min | 21.6 kWh |
| 65% | 1,170 W | 45 min | 28.1 kWh |
| 100% | 1,800 W | 29 min | 43.2 kWh |
Even at a 50% duty cycle the battery lasts 58 min, so plan on solar, grid or generator recharging for anything longer than an evening outage.
3. NEC 125% Breaker & Copper Wire Gauge Sizing
NEC 210.19(A) and 210.20(A) require conductors and overcurrent devices for continuous loads — anything running three hours or more, which includes EV charging and HVAC — to be rated at 125% of the load current. For this pairing: 1,800 W ÷ 120 V = 15.0 A, × 1.25 = 18.8 A, which rounds up to the next standard NEC 240.6 size of 20 A. The conductor must be protected by that breaker (75 °C ampacity at least 20 A) and keep round-trip voltage drop at or below 3%, so longer runs are upsized.
Voltage drop % = (2 × L × I × R) ÷ V × 100
North America (NEC, THHN copper, 75 °C)
| One-way distance | Breaker | Min. copper | Voltage drop | Note |
|---|---|---|---|---|
| 25 ft (7.6 m) | 20 A | 12 AWG | 1.21% | Sized by ampacity |
| 50 ft (15.2 m) | 20 A | 12 AWG | 2.41% | Sized by ampacity |
| 75 ft (22.9 m) | 20 A | 10 AWG | 2.27% | Upsized for voltage drop |
| 100 ft (30.5 m) | 20 A | 8 AWG | 1.91% | Upsized for voltage drop |
UK / EU / Australia (IEC 60364 / BS 7671, PVC copper, method C)
IEC-based codes size protection by design current rather than a blanket 125% multiplier: Ib ≤ In ≤ Iz. At 230 V the load draws 7.8 A, so a 10 A Type B/C MCB with RCD protection applies. In the UK, BS 7671 Section 722 additionally requires a dedicated circuit and Type A or Type B RCD for EV charge points.
| One-way distance | MCB | Min. cable | Voltage drop |
|---|---|---|---|
| 7.5 m (25 ft) | 10 A | 1.5 mm² | 0.62% |
| 15 m (49 ft) | 10 A | 1.5 mm² | 1.24% |
| 22.5 m (74 ft) | 10 A | 1.5 mm² | 1.85% |
| 30 m (98 ft) | 10 A | 1.5 mm² | 2.47% |
Moving the EcoFlow Delta 3 Plus from 25 ft to 100 ft away forces the conductor up from 12 AWG to 8 AWG — park the unit as close to the load as ventilation and weather protection allow.
4. Solar Array Recharge Time Breakdown
The EcoFlow Delta 3 Plus accepts up to 1,000 W of photovoltaic input. Real arrays rarely deliver nameplate output, so we apply an 80% harvest factor for MPPT conversion, cell temperature and soiling, and convert hours to days using 4.5 peak-sun-hours — a conservative annual average for the US, southern Europe and Australia (UK winters can fall below 1.5).
| PV array | Real harvest | 0–100% recharge | Sun-days @ 4.5 PSH | Net with load @ 50% |
|---|---|---|---|---|
| 400 W | 320 W | 3.2 hrs | 0.7 | −580 W |
| 800 W | 640 W | 1.6 hrs | 0.4 | −260 W |
| 1,000 W | 800 W | 1.3 hrs | 0.3 | −100 W |
A typical 800 W portable array refills the battery in about 1.6 hrs of strong sun, while maxing out the 1,000 W input cuts that to 1.3 hrs. To fully offset the Single-Burner Portable Induction Cooktop at a 50% duty cycle (900 W average) during daylight you need roughly 1,150 W of panels, which exceeds this unit's 1,000 W input limit — solar can slow the drain but not eliminate it.
5. Frequently Asked Questions
Can the EcoFlow Delta 3 Plus run a Single-Burner Portable Induction Cooktop?
Yes. The EcoFlow Delta 3 Plus delivers 1,800 W continuous and 3,600 W surge, covering the Single-Burner Portable Induction Cooktop's 1,800 W running and 1,850 W start-up draw at 100% inverter utilization, which is above the 80% guideline, so dedicate the unit to this load.
How long will the EcoFlow Delta 3 Plus run a Single-Burner Portable Induction Cooktop?
With 1,024 Wh of capacity and 85% inverter efficiency, expect about 29 min of continuous operation and 58 min at a 50% duty cycle. Adding solar input during the day extends this further.
What breaker and wire size do I need to connect a Single-Burner Portable Induction Cooktop to the EcoFlow Delta 3 Plus?
In the US, 1,800 W at 120 V is 15.0 A; applying the NEC 125% continuous-load rule gives 18.8 A, so use a 20 A breaker and 12 AWG copper for runs up to 25 ft (1.2% voltage drop). In 230 V markets the load draws 7.8 A, protected by a 10 A MCB on 1.5 mm² cable for runs up to 7.5 m. Receptacle: NEMA 5-15P / 5-20P (US) or BS 1363 13A / Schuko CEE 7/4 / AS/NZS 3112 10A (UK/EU/AU).
How long does it take to recharge the EcoFlow Delta 3 Plus with solar panels?
With an 800 W array and an 80% real-world harvest factor, a full recharge takes about 1.6 hrs of peak sun (0.4 days at 4.5 peak-sun-hours). At its maximum 1,000 W solar input it drops to 1.3 hrs.
Methodology & safety note
Specifications come from manufacturer datasheets in our open dataset; ampacity and resistance values follow NEC Table 310.16 and Chapter 9 Table 8, and BS 7671 Appendix 4. Calculations assume copper conductors, 30 °C ambient and no bundling derating. Inverter-to-panel connections require a listed transfer switch or interlock to prevent back-feeding the grid. These results are an engineering estimate, not a substitute for a licensed electrician and local permit. See our methodology and safety disclaimer.