Engineering report · reviewed against NEC 2026 & BS 7671:2018+A2
Engineering Breakdown: Running a 10,000 BTU Inverter Window Air Conditioner on the Enphase IQ Battery 5P (Dual 10kWh Bank)
When pairing the Enphase IQ Battery 5P (Dual 10kWh Bank) (10,000 Wh LiFePO4 capacity, 7,680 W continuous, 15,360 W surge) with a 10,000 BTU Inverter Window Air Conditioner (880 W running, 1,200 W starting surge), the system operates at 11% of continuous inverter capacity on a 120 V North American circuit and 11% on a 230 V UK/EU/AU circuit. At a 100% duty cycle and 85% inverter efficiency, a full battery delivers roughly 9.7 hrs of off-grid runtime. Wiring the connection over a 25 ft run calls for a 15 A breaker and 14 AWG copper, terminated at a NEMA 5-15P connection.
1. Compatibility Verdict & Inverter Load Utilization
In North American mode the 10,000 BTU Inverter Window Air Conditioner loads the Enphase IQ Battery 5P (Dual 10kWh Bank)'s inverter to 11% of its 7,680 W continuous rating and 8% of its 15,360 W surge rating. Both figures are under the 80% sustained-load guideline, so this is a comfortable, verified match with 6,800 W of spare capacity for lights, a router or a refrigerator on the same unit.
| Check | Load requires | Enphase IQ Battery 5P provides | US/NA | UK/EU/AU |
|---|---|---|---|---|
| Continuous output | 880 W | 7,680 W | Pass | Pass |
| Start-up surge | 1,200 W | 15,360 W | Pass | Pass |
| Voltage | 120 V / 230 V | 120/240 V / 230 V | Pass | Pass |
| Connection | NEMA 5-15P | Hardwired IQ System Controller | UK/EU/AU: BS 1363 13A / Schuko CEE 7/4 / AS/NZS 3112 10A | |
Compressor-driven HVAC equipment is the hardest category for any inverter because of locked-rotor amperage (LRA): for a fraction of a second the motor pulls 1.4× its running power (1,200 W here). The Enphase IQ Battery 5P (Dual 10kWh Bank) is rated for 15,360 W of surge, which covers that inrush. Thermostat cycling means the compressor rarely runs 100% of the time; mild weather typically produces 30–50% duty cycles, while peak summer afternoons push toward 80–100%. Fitting a soft-start module (Micro-Air EasyStart, SoftStartRV or a variable-speed inverter compressor) is the single cheapest way to make a marginal pairing reliable.
The Enphase IQ Battery 5P (Dual 10kWh Bank) is a permanently installed hybrid battery. It sits behind a gateway or system controller, so loads are fed from the home's own panel rather than from outlets on the unit.
2. Real-World Runtime by Duty Cycle
Nameplate capacity is not usable capacity. DC-to-AC conversion, battery management overhead and cell protection reduce the 10,000 Wh rating to about 8,500 Wh of deliverable AC energy (85% system efficiency). Duty cycle is the share of each hour the load actually draws its running power — thermostats, pressure switches and intermittent use all lower it.
| Duty cycle | Average draw | Runtime (no solar) | Energy per 24 h |
|---|---|---|---|
| 25% | 220 W | 38.6 hrs | 5.3 kWh |
| 50% | 440 W | 19.3 hrs | 10.6 kWh |
| 65% | 572 W | 14.9 hrs | 13.7 kWh |
| 100% | 880 W | 9.7 hrs | 21.1 kWh |
Even at a 50% duty cycle the battery lasts 19.3 hrs, so plan on solar, grid or generator recharging for anything longer than an evening outage.
3. NEC 125% Breaker & Copper Wire Gauge Sizing
NEC 210.19(A) and 210.20(A) require conductors and overcurrent devices for continuous loads — anything running three hours or more, which includes EV charging and HVAC — to be rated at 125% of the load current. For this pairing: 880 W ÷ 120 V = 7.3 A, × 1.25 = 9.2 A, which rounds up to the next standard NEC 240.6 size of 15 A. The conductor must be protected by that breaker (75 °C ampacity at least 15 A) and keep round-trip voltage drop at or below 3%, so longer runs are upsized.
Voltage drop % = (2 × L × I × R) ÷ V × 100
North America (NEC, THHN copper, 75 °C)
| One-way distance | Breaker | Min. copper | Voltage drop | Note |
|---|---|---|---|---|
| 25 ft (7.6 m) | 15 A | 14 AWG | 0.94% | Sized by ampacity |
| 50 ft (15.2 m) | 15 A | 14 AWG | 1.88% | Sized by ampacity |
| 75 ft (22.9 m) | 15 A | 14 AWG | 2.81% | Sized by ampacity |
| 100 ft (30.5 m) | 15 A | 12 AWG | 2.36% | Upsized for voltage drop |
UK / EU / Australia (IEC 60364 / BS 7671, PVC copper, method C)
IEC-based codes size protection by design current rather than a blanket 125% multiplier: Ib ≤ In ≤ Iz. At 230 V the load draws 3.8 A, so a 6 A Type B/C MCB with RCD protection applies. In the UK, BS 7671 Section 722 additionally requires a dedicated circuit and Type A or Type B RCD for EV charge points.
| One-way distance | MCB | Min. cable | Voltage drop |
|---|---|---|---|
| 7.5 m (25 ft) | 6 A | 1.5 mm² | 0.30% |
| 15 m (49 ft) | 6 A | 1.5 mm² | 0.60% |
| 22.5 m (74 ft) | 6 A | 1.5 mm² | 0.91% |
| 30 m (98 ft) | 6 A | 1.5 mm² | 1.21% |
Moving the Enphase IQ Battery 5P (Dual 10kWh Bank) from 25 ft to 100 ft away forces the conductor up from 14 AWG to 12 AWG — park the unit as close to the load as ventilation and weather protection allow.
4. Solar Array Recharge Time Breakdown
The Enphase IQ Battery 5P (Dual 10kWh Bank) accepts up to 12,000 W of photovoltaic input. Real arrays rarely deliver nameplate output, so we apply an 80% harvest factor for MPPT conversion, cell temperature and soiling, and convert hours to days using 4.5 peak-sun-hours — a conservative annual average for the US, southern Europe and Australia (UK winters can fall below 1.5).
| PV array | Real harvest | 0–100% recharge | Sun-days @ 4.5 PSH | Net with load @ 50% |
|---|---|---|---|---|
| 800 W | 640 W | 15.6 hrs | 3.5 | +200 W |
| 1,600 W | 1,280 W | 7.8 hrs | 1.7 | +840 W |
| 3,000 W | 2,400 W | 4.2 hrs | 0.9 | +1,960 W |
| 6,000 W | 4,800 W | 2.1 hrs | 0.5 | +4,360 W |
| 12,000 W | 9,600 W | 1.0 hrs | 0.2 | +9,160 W |
A typical 800 W portable array refills the battery in about 15.6 hrs of strong sun, while maxing out the 12,000 W input cuts that to 1.0 hrs. To fully offset the 10,000 BTU Inverter Window Air Conditioner at a 50% duty cycle (440 W average) during daylight you need roughly 550 W of panels, which this unit can accept.
5. Frequently Asked Questions
Can the Enphase IQ Battery 5P (Dual 10kWh Bank) run a 10,000 BTU Inverter Window Air Conditioner?
Yes. The Enphase IQ Battery 5P (Dual 10kWh Bank) delivers 7,680 W continuous and 15,360 W surge, covering the 10,000 BTU Inverter Window Air Conditioner's 880 W running and 1,200 W start-up draw at 11% inverter utilization.
How long will the Enphase IQ Battery 5P (Dual 10kWh Bank) run a 10,000 BTU Inverter Window Air Conditioner?
With 10,000 Wh of capacity and 85% inverter efficiency, expect about 9.7 hrs of continuous operation and 19.3 hrs at a 50% duty cycle. Adding solar input during the day extends this further.
What breaker and wire size do I need to connect a 10,000 BTU Inverter Window Air Conditioner to the Enphase IQ Battery 5P (Dual 10kWh Bank)?
In the US, 880 W at 120 V is 7.3 A; applying the NEC 125% continuous-load rule gives 9.2 A, so use a 15 A breaker and 14 AWG copper for runs up to 25 ft (0.9% voltage drop). In 230 V markets the load draws 3.8 A, protected by a 6 A MCB on 1.5 mm² cable for runs up to 7.5 m. Receptacle: NEMA 5-15P (US) or BS 1363 13A / Schuko CEE 7/4 / AS/NZS 3112 10A (UK/EU/AU).
How long does it take to recharge the Enphase IQ Battery 5P (Dual 10kWh Bank) with solar panels?
With an 800 W array and an 80% real-world harvest factor, a full recharge takes about 15.6 hrs of peak sun (3.5 days at 4.5 peak-sun-hours). At its maximum 12,000 W solar input it drops to 1.0 hrs.
Methodology & safety note
Specifications come from manufacturer datasheets in our open dataset; ampacity and resistance values follow NEC Table 310.16 and Chapter 9 Table 8, and BS 7671 Appendix 4. Calculations assume copper conductors, 30 °C ambient and no bundling derating. Inverter-to-panel connections require a listed transfer switch or interlock to prevent back-feeding the grid. These results are an engineering estimate, not a substitute for a licensed electrician and local permit. See our methodology and safety disclaimer.