Engineering report · reviewed against NEC 2026 & BS 7671:2018+A2
Engineering Breakdown: Running a 60-Gallon 3.7 HP Stationary Shop Air Compressor on the myenergi Libbi (5kW Inverter + 5kWh Battery)
When pairing the myenergi Libbi (5kW Inverter + 5kWh Battery) (5,120 Wh LiFePO4 capacity, 5,000 W continuous, 7,500 W surge) with a 60-Gallon 3.7 HP Stationary Shop Air Compressor (3,400 W running, 7,800 W starting surge), the system operates at 68% of continuous inverter capacity on a 230 V UK/EU/AU circuit. Our UK/EU/AU verdict is Surge Overload, so the runtime figures below are theoretical battery-energy values only. Wiring the connection over a 7.5 m run calls for a 16 A MCB and 1.5 mm² copper, terminated at a IEC 60309 16A Commando / Schuko 16A connection.
1. Compatibility Verdict & Inverter Load Utilization
In UK/EU/AU 230 V mode the 60-Gallon 3.7 HP Stationary Shop Air Compressor loads the myenergi Libbi (5kW Inverter + 5kWh Battery)'s inverter to 68% of its 5,000 W continuous rating and 104% of its 7,500 W surge rating. Running watts fit, but the start-up surge exceeds what the inverter can deliver even momentarily, so expect an overload trip each time the motor starts. A soft-start device or stepping up to the Oukitel BP5000 Pro Max resolves it.
| Check | Load requires | myenergi Libbi provides | UK/EU/AU |
|---|---|---|---|
| Continuous output | 3,400 W | 5,000 W | Pass |
| Start-up surge | 7,800 W | 7,500 W | Fail |
| Voltage | 230 V | 230 V | Pass |
| Connection | IEC 60309 16A Commando / Schuko 16A | Hardwired consumer unit (RCBO protected) |
Workshop tools combine high running watts with brutal start-up spikes: universal motors and induction motors reach 2.3× their running draw (7,800 W) when the blade, drum or compressor head spins up under load. Because tool use is intermittent — measured in minutes per hour rather than hours per day — battery capacity is rarely the limit, but inverter surge capacity is. At 7,500 W of surge, the myenergi Libbi (5kW Inverter + 5kWh Battery) will likely shut down the moment the motor starts. Avoid long, thin extension cords on job sites; voltage sag at the tool increases current and heat.
The myenergi Libbi (5kW Inverter + 5kWh Battery) is a UK smart home storage system, installed on a dedicated circuit from the consumer unit under BS 7671 and typically paired with a time-of-use tariff to charge overnight and discharge at peak. Backup operation for specific circuits depends on the installer fitting an EPS/backup switch.
Compatible alternative: the Oukitel BP5000 Pro Max with the 60-Gallon 3.7 HP Stationary Shop Air Compressor report shows the full sizing for a unit that passes all three checks.
2. Real-World Runtime by Duty Cycle
Nameplate capacity is not usable capacity. DC-to-AC conversion, battery management overhead and cell protection reduce the 5,120 Wh rating to about 4,352 Wh of deliverable AC energy (85% system efficiency). Duty cycle is the share of each hour the load actually draws its running power — thermostats, pressure switches and intermittent use all lower it.
| Duty cycle | Average draw | Runtime (no solar) | Energy per 24 h |
|---|---|---|---|
| 25% | 850 W | 5.1 hrs | 20.4 kWh |
| 50% | 1,700 W | 2.6 hrs | 40.8 kWh |
| 65% | 2,210 W | 2.0 hrs | 53.0 kWh |
| 100% | 3,400 W | 1.3 hrs | 81.6 kWh |
Even at a 50% duty cycle the battery lasts 2.6 hrs, so plan on solar, grid or generator recharging for anything longer than an evening outage. Because the inverter cannot actually run this load in UK/EU/AU mode, treat these numbers as an energy-budget reference for a compatible inverter of the same capacity.
3. BS 7671 / IEC 60364 Breaker & Cable Sizing
IEC-based codes size protection by design current rather than a blanket 125% multiplier: Ib ≤ In ≤ Iz. At 230 V the load draws 14.8 A, so a 16 A Type B/C MCB with RCD protection applies. In the UK, BS 7671 Section 722 additionally requires a dedicated circuit and Type A or Type B RCD for EV charge points.
| One-way distance | MCB | Min. cable | Voltage drop |
|---|---|---|---|
| 7.5 m (25 ft) | 16 A | 1.5 mm² | 1.17% |
| 15 m (49 ft) | 16 A | 1.5 mm² | 2.33% |
| 22.5 m (74 ft) | 16 A | 2.5 mm² | 2.14% |
| 30 m (98 ft) | 16 A | 2.5 mm² | 2.86% |
Moving the myenergi Libbi (5kW Inverter + 5kWh Battery) from 7.5 m to 30 m away forces the conductor up from 1.5 mm² to 2.5 mm² — park the unit as close to the load as ventilation and weather protection allow.
4. Solar Array Recharge Time Breakdown
The myenergi Libbi (5kW Inverter + 5kWh Battery) accepts up to 5,000 W of photovoltaic input. Real arrays rarely deliver nameplate output, so we apply an 80% harvest factor for MPPT conversion, cell temperature and soiling, and convert hours to days using 4.5 peak-sun-hours — a conservative annual average for the US, southern Europe and Australia (UK winters can fall below 1.5).
| PV array | Real harvest | 0–100% recharge | Sun-days @ 4.5 PSH | Net with load @ 50% |
|---|---|---|---|---|
| 400 W | 320 W | 16.0 hrs | 3.6 | −1,380 W |
| 800 W | 640 W | 8.0 hrs | 1.8 | −1,060 W |
| 1,600 W | 1,280 W | 4.0 hrs | 0.9 | −420 W |
| 3,000 W | 2,400 W | 2.1 hrs | 0.5 | +700 W |
| 5,000 W | 4,000 W | 1.3 hrs | 0.3 | +2,300 W |
A typical 800 W portable array refills the battery in about 8.0 hrs of strong sun, while maxing out the 5,000 W input cuts that to 1.3 hrs. To fully offset the 60-Gallon 3.7 HP Stationary Shop Air Compressor at a 50% duty cycle (1,700 W average) during daylight you need roughly 2,150 W of panels, which this unit can accept.
5. Frequently Asked Questions
Can the myenergi Libbi (5kW Inverter + 5kWh Battery) run a 60-Gallon 3.7 HP Stationary Shop Air Compressor?
Not reliably in the UK, Europe and Australia — our verdict is "Surge Overload". The 7,800 W start-up surge exceeds the 7,500 W surge rating. The Oukitel BP5000 Pro Max is a compatible alternative.
How long will the myenergi Libbi (5kW Inverter + 5kWh Battery) run a 60-Gallon 3.7 HP Stationary Shop Air Compressor?
With 5,120 Wh of capacity and 85% inverter efficiency, expect about 1.3 hrs of continuous operation and 2.6 hrs at a 50% duty cycle — theoretical figures, since the inverter cannot actually sustain this load. Adding solar input during the day extends this further.
What breaker and wire size do I need to connect a 60-Gallon 3.7 HP Stationary Shop Air Compressor to the myenergi Libbi (5kW Inverter + 5kWh Battery)?
At 230 V the load draws 14.8 A. Under BS 7671 / IEC 60364 the protective device must be at least the design current (Ib ≤ In ≤ Iz), so use a 16 A MCB with RCD protection on 1.5 mm² copper cable for runs up to 7.5 m (1.2% voltage drop). Connection: IEC 60309 16A Commando / Schuko 16A.
How long does it take to recharge the myenergi Libbi (5kW Inverter + 5kWh Battery) with solar panels?
With an 800 W array and an 80% real-world harvest factor, a full recharge takes about 8.0 hrs of peak sun (1.8 days at 4.5 peak-sun-hours). At its maximum 5,000 W solar input it drops to 1.3 hrs.
Methodology & safety note
Specifications come from manufacturer datasheets in our open dataset; ampacity and resistance values follow NEC Table 310.16 and Chapter 9 Table 8, and BS 7671 Appendix 4. Calculations assume copper conductors, 30 °C ambient and no bundling derating. Inverter-to-panel connections require a listed transfer switch or interlock to prevent back-feeding the grid. These results are an engineering estimate, not a substitute for a licensed electrician and local permit. See our methodology and safety disclaimer.