Engineering report · reviewed against NEC 2026 & BS 7671:2018+A2
Engineering Breakdown: Running a Chevy Equinox EV (Level 1 120V / 12A Cord) on the Pecron E3600LFP
When pairing the Pecron E3600LFP (3,072 Wh LiFePO4 capacity, 3,600 W continuous, 7,000 W surge) with a Chevy Equinox EV (Level 1 120V / 12A Cord) (1,440 W running, 1,440 W starting surge), the system operates at 40% of continuous inverter capacity on a 120 V North American circuit and 77% on a 230 V UK/EU/AU circuit. At a 100% duty cycle and 85% inverter efficiency, a full battery delivers roughly 1.8 hrs of off-grid runtime. Wiring the connection over a 25 ft run calls for a 15 A breaker and 14 AWG copper, terminated at a NEMA 5-15P connection.
1. Compatibility Verdict & Inverter Load Utilization
In North American mode the Chevy Equinox EV (Level 1 120V / 12A Cord) loads the Pecron E3600LFP's inverter to 40% of its 3,600 W continuous rating and 21% of its 7,000 W surge rating. Both figures are under the 80% sustained-load guideline, so this is a comfortable, verified match with 2,160 W of spare capacity for lights, a router or a refrigerator on the same unit.
| Check | Load requires | Pecron E3600LFP provides | US/NA | UK/EU/AU |
|---|---|---|---|---|
| Continuous output | 1,440 W (2,760 W @ 230V) | 3,600 W | Pass | Pass |
| Start-up surge | 1,440 W | 7,000 W | Pass | Pass |
| Voltage | 120 V / 230 V | 120 V / 230 V | Pass | Pass |
| Connection | NEMA 5-15P | NEMA TT-30R / 5-20R | UK/EU/AU: Type 2 EVSE · IEC 60309 16A Commando | |
An EVSE is a constant-current device: the vehicle draws exactly the current advertised by the J1772/NACS pilot signal, so the 1,440 W figure is both the running load and the start-up load — there is no motor inrush. That makes the calculation unusually clean. If you want to stay under the 80% sustained-load guideline, set the charge current in the vehicle app to 24 A or less, which keeps the Pecron E3600LFP at roughly 2,880 W. A full battery delivers about 2.4 kWh into the pack after inverter and on-board charger losses, worth roughly 8 miles (13 km) of driving at 3.5 mi/kWh.
As a portable power station, the Pecron E3600LFP integrates the LiFePO4 battery, inverter, MPPT solar controller and AC outlets in one chassis, so it can be wheeled to the load or connected to a transfer switch through its NEMA TT-30R / 5-20R outlet.
2. Real-World Runtime by Duty Cycle
Nameplate capacity is not usable capacity. DC-to-AC conversion, battery management overhead and cell protection reduce the 3,072 Wh rating to about 2,611 Wh of deliverable AC energy (85% system efficiency). EV charging runs at a fixed current, so the 100% row is the realistic figure; lower rows apply only if you schedule charging in intervals.
| Duty cycle | Average draw | Runtime (no solar) | Energy per 24 h |
|---|---|---|---|
| 25% | 360 W | 7.3 hrs | 8.6 kWh |
| 50% | 720 W | 3.6 hrs | 17.3 kWh |
| 65% | 936 W | 2.8 hrs | 22.5 kWh |
| 100% | 1,440 W | 1.8 hrs | 34.6 kWh |
Even at a 50% duty cycle the battery lasts 3.6 hrs, so plan on solar, grid or generator recharging for anything longer than an evening outage.
3. NEC 125% Breaker & Copper Wire Gauge Sizing
NEC 210.19(A) and 210.20(A) require conductors and overcurrent devices for continuous loads — anything running three hours or more, which includes EV charging and HVAC — to be rated at 125% of the load current. For this pairing: 1,440 W ÷ 120 V = 12.0 A, × 1.25 = 15.0 A, which rounds up to the next standard NEC 240.6 size of 15 A. The conductor must be protected by that breaker (75 °C ampacity at least 15 A) and keep round-trip voltage drop at or below 3%, so longer runs are upsized.
Voltage drop % = (2 × L × I × R) ÷ V × 100
North America (NEC, THHN copper, 75 °C)
| One-way distance | Breaker | Min. copper | Voltage drop | Note |
|---|---|---|---|---|
| 25 ft (7.6 m) | 15 A | 14 AWG | 1.53% | Sized by ampacity |
| 50 ft (15.2 m) | 15 A | 12 AWG | 1.93% | Upsized for voltage drop |
| 75 ft (22.9 m) | 15 A | 12 AWG | 2.89% | Upsized for voltage drop |
| 100 ft (30.5 m) | 15 A | 10 AWG | 2.42% | Upsized for voltage drop |
UK / EU / Australia (IEC 60364 / BS 7671, PVC copper, method C)
IEC-based codes size protection by design current rather than a blanket 125% multiplier: Ib ≤ In ≤ Iz. At 230 V the load draws 12.0 A (the EVSE's 12 A pilot current at 230 V), so a 13 A Type B/C MCB with RCD protection applies. In the UK, BS 7671 Section 722 additionally requires a dedicated circuit and Type A or Type B RCD for EV charge points.
| One-way distance | MCB | Min. cable | Voltage drop |
|---|---|---|---|
| 7.5 m (25 ft) | 13 A | 1.5 mm² | 0.95% |
| 15 m (49 ft) | 13 A | 1.5 mm² | 1.89% |
| 22.5 m (74 ft) | 13 A | 1.5 mm² | 2.84% |
| 30 m (98 ft) | 13 A | 2.5 mm² | 2.32% |
Moving the Pecron E3600LFP from 25 ft to 100 ft away forces the conductor up from 14 AWG to 10 AWG — park the unit as close to the load as ventilation and weather protection allow.
4. Solar Array Recharge Time Breakdown
The Pecron E3600LFP accepts up to 2,400 W of photovoltaic input. Real arrays rarely deliver nameplate output, so we apply an 80% harvest factor for MPPT conversion, cell temperature and soiling, and convert hours to days using 4.5 peak-sun-hours — a conservative annual average for the US, southern Europe and Australia (UK winters can fall below 1.5).
| PV array | Real harvest | 0–100% recharge | Sun-days @ 4.5 PSH | Net with load @ 50% |
|---|---|---|---|---|
| 400 W | 320 W | 9.6 hrs | 2.1 | −400 W |
| 800 W | 640 W | 4.8 hrs | 1.1 | −80 W |
| 1,600 W | 1,280 W | 2.4 hrs | 0.5 | +560 W |
| 2,400 W | 1,920 W | 1.6 hrs | 0.4 | +1,200 W |
A typical 800 W portable array refills the battery in about 4.8 hrs of strong sun, while maxing out the 2,400 W input cuts that to 1.6 hrs. To fully offset the Chevy Equinox EV (Level 1 120V / 12A Cord) at a 50% duty cycle (720 W average) during daylight you need roughly 900 W of panels, which this unit can accept.
5. Frequently Asked Questions
Can the Pecron E3600LFP run a Chevy Equinox EV (Level 1 120V / 12A Cord)?
Yes. The Pecron E3600LFP delivers 3,600 W continuous and 7,000 W surge, covering the Chevy Equinox EV (Level 1 120V / 12A Cord)'s 1,440 W running and 1,440 W start-up draw at 40% inverter utilization.
How many miles of range can the Pecron E3600LFP add to a Chevy Equinox EV?
A full 3,072 Wh charge delivers about 2.4 kWh to the vehicle battery after inverter (85%) and on-board charger (90%) losses — roughly 8 miles at 3.5 mi/kWh. At the full 1,440 W charge rate that takes 1.8 hrs.
What breaker and wire size do I need to connect a Chevy Equinox EV (Level 1 120V / 12A Cord) to the Pecron E3600LFP?
In the US, 1,440 W at 120 V is 12.0 A; applying the NEC 125% continuous-load rule gives 15.0 A, so use a 15 A breaker and 14 AWG copper for runs up to 25 ft (1.5% voltage drop). In 230 V markets the load draws 12.0 A, protected by a 13 A MCB on 1.5 mm² cable for runs up to 7.5 m. Receptacle: NEMA 5-15P (US) or Type 2 EVSE · IEC 60309 16A Commando (UK/EU/AU).
How long does it take to recharge the Pecron E3600LFP with solar panels?
With an 800 W array and an 80% real-world harvest factor, a full recharge takes about 4.8 hrs of peak sun (1.1 days at 4.5 peak-sun-hours). At its maximum 2,400 W solar input it drops to 1.6 hrs.
Methodology & safety note
Specifications come from manufacturer datasheets in our open dataset; ampacity and resistance values follow NEC Table 310.16 and Chapter 9 Table 8, and BS 7671 Appendix 4. Calculations assume copper conductors, 30 °C ambient and no bundling derating. Inverter-to-panel connections require a listed transfer switch or interlock to prevent back-feeding the grid. These results are an engineering estimate, not a substitute for a licensed electrician and local permit. See our methodology and safety disclaimer.